SALT-FREE WATER SOFTENER TRIO TAC NEXT SCALE STOP NSS-110B-T

Trio TAC TAC Next Scale Stop NSS-110B-T Salt-Free Dedurizer, uses salt-free technology called Template Assisted Crystallization.

Tested and verified!

Tested by independent laboratory to prevent deposits,  The TAC Next Scale Stop has a 99.6% rating for deposit prevention, the only technology to achieve this performance, being more effective than any other alternative.

TAC certifications, Next Scale Stop: NSF standard 61

          
Recommended for a continuous flow of: 10 l/minute and for peak flows up to 15 l/minute.

Maximum recommended hardness: 72.8 German degrees

Note: TAC technology does not work like a classic water softener, by ion exchange and by replacing calcium and magnesium salts with sodium in the water. From this point of view, it should be called a water softener or more correctly a conditioner. So bear in mind that it is not a traditional softener and that the calcium and magnesium ions remain in the water but in a form that stops deposits. So, the hardness of the water will remain the same before and after treatment with TAC.

Trio TAC Next Scale Next Stop NSS-110B-T - prevents deposits in installations and protects equipment. In addition, it filters water to a 5 micron grade and dechlorinates water. 

Limescale deposits in the plumbing, block pipes, faucets, destroy the central heating system and boiler. With TAC next NSS-110B, you will save money and have time for yourself, not time for repairs!

Trio TAC Next Scale Next Stop NSS-110B-T - By using TAC technology, you remove existing deposits in installations and considerably extend the life of water-using equipment. If you have used untreated hard water, deposits have formed in the installations. Using TAC technology will gradually clean the installation. The classic water softener cannot do this!

No chemicals needed - green - environmentally friendly!
The classic softener uses salt for regeneration, which is not at all economical and environmentally friendly, as this brine has to be discharged to the sewer after the regeneration process.

It's 100% environmentally friendly and economical without buying salt. Because Trio TAC Next Scale Next Stop NSS-110B-T not using salt, you'll save money that you can use for anything else.

Minimum maintenance and low costs
Classical softening plants contain electronic or mechanical control valves that need maintenance and periodic cleaning. This requires specialists, which means costs for you. Trio TAC Next Scale Next Stop NSS-110B-T contains no moving parts so absolutely nothing can wear.

No electricity - installed anywhere
Trio TAC Next Scale Stop NSS-110B-T TAC Next Scale Stop NSS-110B-T, it doesn't use electricity, and it doesn't discharge water to the sewer. So it can be installed anywhere!

Cost savings
TAC Trio TAC Next Scale Stop NSS-110B-T - TAC Trio TAC Next Scale Stop NSS-110B-T - it pays for itself in time, because you no longer buy salt, you no longer use electricity, you no longer pour water into the sewer, pumped by electricity or paid to the water authority!

Did you know that 1 mm of limescale in your boiler or central heating system reduces the heating output by 10%? And this deposition occurs in less than a year! And in three years it will reduce the heating output by up to 241TP33T!

Replacement parts
Because nothing in this world lasts forever, the filtering cartridges have to be changed. 

Filters included in Trio TAC Next Scale Stop NSS-110B-T:

• 5 micron - pressed polypropylene fibers - for filtering sediment, silt, silt, sand, rust;
• activated carbon block for dechlorination;
• TAC anti-scaling TAC

Installation conditions:

- will be installed at the entrance of the house on the main cold water pipe;
- if there is more than one treatment/filtration equipment, install the last one in the filtration scheme;
- to be installed before any domestic or heating equipment, which is intended to be protected from limescale;
- if the installation is made of copper, the water will be used for four weeks before it is treated and run through the Trio TAC Next Scale Stop NSS-110B-T TAC Next Scale Stop NSS-110B-T. TAC technology is not allowed to come into contact with copper. After use for four weeks, the copper pipes will be passivated, and this will prevent copper ions from entering the TAC filter medium;
- we recommend the installation of a bypass, consisting of pipes and three valves, in case of service or change of filter medium.

Water quality because Softener Trio TAC Next Scale Stop NSS-110B-T to be used:

Feed water/treatment water must meet the following conditions:

pH 6.5 - 8.5
Maximum hardness - 72.8 German degrees
Min/max pressure -1-5 bar (we recommend using with a max. pressure of 4.5 bar)
Temperature - 5°C to 43°C
Chlorine - < 3ppm
Iron (maximum) - 0.3 mg/l
Manganese (maximum) - 0.05 mg/l
Copper - 1.3 mg/l
Oil/petrol and hydrogen sulphide - not allowed
Polyphosphate - not allowed
Silicon (maximum) - 10 ppm

If the water is from a controlled source (waterworks) and meets drinking water standards, it is not necessary to carry out a water analysis.

Technical specifications:
Connections: 1″ IN/OUT;
Length: 62 cm
Height: 47 cm;
Diameter: 20 cm.

Maintenance:

Two cartridges will be changed every 3 - 6 months

The filter cartridge for anti-scale treatment will be changed every 2 years.

2-year guarantee

Assembled in Romania. We use TAC Next Scale Stop (UK).